First Flush Diverters: What They Do and Whether You Need One

first flush diverter

Wondering if you need a first flush diverter? It sends the first, dirtiest roof runoff to a catchment pipe instead of your tank. For roof-fed systems, a university extension guide lists it as a standard component.

This guide is part of our wider look at rainwater harvesting, and it focuses on one small but useful part of the setup.

Item Value
Minimum first flush volume 10 gallons per 1,000 square feet of collection surface, for a 1 inch rainfall
Typical leaf screen mesh ¼-inch-square wire frames
Filter in most roof washer units 30-micron
Standard residential gutter width 4 to 6 inches
Downspout area for roof runoff 1 square inch per 100 square feet of roof area

These figures come from the LSU AgCenter guide to rainwater harvesting for small nurseries and home gardens. They can change, and your roof and climate will differ, so check the source before you rely on them.

What a first flush diverter does

When rain starts, the water running off your roof carries whatever has settled there since the last storm. A first flush diverter routes that initial flow off the roof into a catchment pipe, so it never reaches the storage tank (LSU AgCenter).

Leaf screens already stop the large debris. The diverter deals with what gets past them: rocks, bird feces, dirt and moss are collected in the pipe and kept out of the tank, according to the same guide.

The stored water is then better suited to the jobs rainwater is normally used for. The extension guide names nonpotable uses such as irrigation, washing and flushing. For anything involving drinking water, ask your local health authority rather than relying on a garden-focused guide.

Where it sits in the system

The diverter is one step in a chain. Water flows from the roof into the gutters, past a leaf screen, through the diverter, then on to any filter and finally the storage tank.

  1. Roof: the collection surface.
  2. Leaf screen: stops large debris at the gutter.
  3. Gutter and downspout: carry the flow toward the tank.
  4. First flush diverter: catches the dirtiest initial runoff.
  5. Primary filter: positioned before the storage tank.
  6. Storage tank: holds the cleaner water for use.

The leaf screens in the LSU AgCenter guide are typically ¼-inch-square wire frames that fit on the gutter (source). The guide also notes that standard residential gutters are 4 to 6 inches wide. If you are still planning that upstream part, our piece on gutters and downspouts for rainwater collection covers it in more detail.

Pipe wrenches and metal pipe fittings lie on a wooden surface.

Downspout sizing matters too. The guide gives 1 square inch of downspout area for every 100 square feet of roof area, as described in the LSU AgCenter publication.

How much water should it divert?

The guide’s rule of thumb is a general first flush diversion of at least 10 gallons for every 1,000 square feet of collection surface, for a 1 inch rainfall (LSU AgCenter). Treat that as a minimum, not a target to hit exactly.

The right volume for your roof depends on several things, which the same source lists:

  • the amount of contaminants on the roof surface
  • the number of dry days between rains
  • the extent of tree overhang
  • the season

Roof shape plays a part as well. Steep roofs shed a quick first flush that the diverter can catch, while a flatter roof may have a more delayed flushing of contaminants, which makes removal harder.

Do you need one?

If you collect from a roof, the extension guide treats a diverter as part of the standard design, so for most roof-fed systems the answer leans toward yes. The case is stronger when your roof is shaded by trees, when long dry spells let dirt build up, or when you use the water on drip irrigation, where clogs are a nuisance.

The guide also says all roof types can be used, but that you should watch for debris coming off asphalt and shingles compared with materials such as metal (LSU AgCenter). That makes roofing material another factor in your decision.

A diverter is not a substitute for a filter. The same publication says a primary filter is typically used for drip irrigation but is a best practice for removing more contaminants, and that it should sit before the storage tank.

Local rules on collecting rainwater vary, so check what applies where you live before you build.

Keeping it working

A diverter only helps if it has room to catch the next flush. The guide says the pipe needs regular maintenance and cleaning, and that opening the valve both flushes out contaminants and restores volume for the next first flush.

Its best-practice advice is to open the valve after each large rain event so concentrated contaminants and small debris don’t sit in the pipe (LSU AgCenter). In seasons of continuous rainfall, the diverters can be cleaned less often.

Common designs are called roof washers or PVC standpipes. Most roof washer units come with 30-micron filters, though you can also build homemade filters from air and dust vent filter material, per the same guide.

Once the tank is full, extra flow needs somewhere to go, which is covered in our guide to rain barrel overflow.

Frequently asked questions

Is a first flush diverter the same as a leaf screen?

Show answer

No. A leaf screen sits on the gutter and blocks large pieces such as leaves, while the diverter handles finer material by capturing the opening runoff in a separate pipe.

What are the usual types?

Show answer

The LSU AgCenter guide names roof washers and PVC standpipes as the most common kinds. Both work by holding back the first part of each storm’s runoff.

How often should I empty it?

Show answer

The guide recommends opening the valve after every large rain event. When rain is falling continuously through a season, you can clean the diverter less frequently.

Can I drink water collected this way?

Show answer

This site does not make claims about drinking rainwater. The source guide covers nonpotable uses, so contact your local health authority about potability.